Skip to main content

MIUI: Connecting to MJX Bugs B2W

I recently purchased the MJX Bugs B2W drone, and had a lot of difficulty connecting to the onboard 5GHz WIFI camera from the Bugs Go app. I finally figured out the solution, and it was totally unexpected, so I thought I'd share it here for anyone faced with the same issue.

I am using the Redmi Note 4 to connect, and that phone supported 5GHz WIFI, so I had no problem connecting to the drone hotspot. But when I launched the Bugs Go app, I keep getting the "Aircraft not connected" message. I tried a couple of stuff, including resetting the 5GHz channel used by the drone (by pressing on the "Camera" button on the remote controller for about 8 seconds, until you hear 3 beeps). Nothing worked.

Then I realized when I connect to the drone hotspot and run Bugs Go, I see this message:


It didn't occur to me initally to tap on the message, because I already knew the drone hotspot had no Internet acess. So out of desperation, I tapped on the message:


By selecting "Stay connected", Bugs Go was immediately able to connect to the drone and started streaming the live video feed from the camera.

Lesson learned!

Labels:

Comments

  1. Beto27 August 2018 at 06:28

    Great man! I'm having the same problem! will give it a try!

    ReplyDelete
  2. EPlan19 December 2019 at 05:49

    You just saved me a lot of frustration. Having the same problem and your guidance fixed it. Thank you!

    ReplyDelete

Post a Comment

Popular posts from this blog

Update: Line adapter for Ozito Blade Trimmer

Update (Dec 2021): If you access to a 3D printer, I would now recommend this solution , which makes it super easy to replace the trimmer line. I have been using it for a few months now with zero issue.
5 comments
Read more

Attiny85 timer programming using Timer1

This Arduino sketch uses Timer1 to drive the LED blinker: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 /* * Program ATTiny85 to blink LED connected to PB1 at 1s interval. * Assumes ATTiny85 is running at 1MHz internal clock speed. */ #include <avr/io.h> #include <avr/wdt.h> #include <avr/sleep.h> #include <avr/interrupt.h> bool timer1 = false , led = true ; // Interrupt service routine for timer1 ISR(TIMER1_COMPA_vect) { timer1 = true ; } void setup() { // Setup output pins pinMode( 1 , OUTPUT); digitalWrite( 1 , led); set_sleep_mode(SLEEP_MODE_IDLE); // Setup timer1 to interrupt every second TCCR1 = 0 ; // Stop timer TCNT1 = 0 ; // Zero timer GTCCR = _BV(PSR1); // Reset prescaler OCR1A = 243 ; // T = prescaler / 1MHz = 0.004096s; OCR1A = (1s/T) - 1 = 243 OCR1C = 243 ; // Set to same value to reset timer1 to
2 comments
Read more

3D Printer Filament Joiner

I have been looking at various ways of joining 3D printing filaments. One method involves running one end of a filament through a short PTFE tubing, melting it with a lighter or candle, retracting it back into the tubing and immediately plunging the filament to be fused into the tubing: One problem with this method is that you can't really control the temperature at which you melt the filament, so you frequently end up with a brittle joint that breaks upon the slightest bend. Aliexpress even sells a contraption that works along the same line. As it uses a lighter or candle as well, it suffers from the same weakness. I am not even sure why you need a special contraption when a short PTFE tubing will work just as well. Another method involves using shrink tubing/aluminium foil, and a heat gun: But a heat gun is rather expensive, so I wanted to explore other alternatives. The candle + PTFE tubing method actually works quite well when you happen to melt it at the rig
1 comment
Read more